基于多材质复合管柱的裸眼井壁支撑工艺及应用

已完钻超深裸眼水平井侧钻技术是经济、高效开发油藏剩余油的主要手段之一，传统的磨铣钢套管开窗侧钻技术存在下入摩阻大、磨铣耗时长导致开窗失败等问题。为此，提出了基于多材质复合管柱的超深水平井裸眼井壁支撑工艺，结合中国西北油田已完钻超深裸眼水平井井况，首先，提出了基于“铝合金+碳钢”的多材质复合管柱组合及设计方法；其次，开展了基于管柱实物屈曲实验数据的管柱临界屈曲载荷计算模型适用性评价，并优选出了适合于“铝合金+碳钢”多材质复合管柱的屈曲临界载荷计算模型；最后，研究了综合考虑管柱扭矩、摩阻、刚性、井眼条件、管柱强度及材质的多材质复合管柱下入性分析方法，并利用下入性分析软件对西北油田顺北X1井、X2井、X3井、X4井复合管柱进行了下入可行性评价。该方法在X1井和X2井得到成功应用，进一步论证了该工艺现场应用的可行性。研究成果可为超深水平井裸眼井壁支撑的复合管柱设计和下入可行性评价提供理论参考。     

一种基于类不平衡学习的情感分析方法

针对网络评论中普遍存在的负面评论较少而影响力却较大的类不平衡问题, 提出一种基于类不平衡学习的情感分析方法. 该方法利用深度学习训练过程中的概率输出, 以计算样例的信息熵作为影响因子构建交叉信息熵损失函数. 在IMDB公开数据集上进行实验验证的结果表明, 基于集成信息熵损失函数的双向长短期记忆网络能处理类不平衡问题; 对数据的统计分析结果表明, 该策略能提升基于双向长短期记忆网络的评论情感极性分类性能. 针对AUC(area under curve)指标, 使用集成信息熵损失函数的双向长短期记忆网络模型比未考虑类不平衡的深度学习模型在中位数上最多提升15.3%.     

Effect of Al on microstructure and mechanical properties of as-extruded Mg–1Mn alloy sheet

The effect of Al addition on microstructure and mechanical properties of hot extruded Mg–1 Mn alloy sheet was investigated. The results revealed that the dynamic recrystallization was promoted by increasing Al content. The ultimate tensile strength and yield strength of the alloy increased with the increase of Al content. The Mg–9 Al–1 Mn alloy exhibited the highest strength, with tensile strength of 308 MPa, 307 MPa, 319 MPa, yield strength of 199 MPa, 207 MPa, 220 MPa and the elongation of 20.9%, 20.1%, 19.2% in 0°, 45°, 90°, respectively.The high strength was mainly attributed to the formation of fine dynamically recrystallized grains and large amounts of the second phase. The strengthening mechanism of the alloys was explained.     

Effect of heat treatment on microstructures and properties of a novel Al-Zn-Mg-Cu alloy for oil drilling

In view of the special requirements for strength, heat resistance and corrosion resistance of Al-Zn-Mg-Cu alloy for oil drilling, the Al-6.2 Zn-2.5 Mg-1.6 Cu alloy was prepared by increasing Cu content on basis of Russian Series 1953 alloy. The effect of heat treatment on the microstructures and properties of the alloy was characterized by optical microscope(OM), scanning electron microscope(SEM) and transmission electron microscope(TEM), and investigated by tensile test at room temperature, thermal exposure test and corrosion test. The results show that the strength after T6 aging treatment exhibit a decrease trend as an increase of the solution temperature from465 °C to 480 °C. After the solution treated by the rate of 470 °C/1 h, second phases dissolve into the matrix very well and the strength property reaches optimum. The alloy has better comprehensive properties treated by a solution treatment of 470 °C/1 h and then followed by an aging treatment of 120 °C/24 h + 170 °C/1 h + 120 °C/24 h. Under the aging state, the precipitated phases inside the grains are suitable in size, while on the grain boundary distribute discontinuously and the precipitate-free zone is obvious. Besides, the alloy still maintain high tensile properties. The yield strength, tensile strength and elongation are 650 MPa, 686 MPa,12.0%, respectively. The yield strength retention after heat exposure is 92%. The alloy has good corrosion resistance and the exfoliation corrosion degree. The average corrosion rate in the H_2S and CO_2 environment is 0.0024 mm/a, which is far less than the required 0.12 mm/a. It is insensitive to H_2S and CO_2 environments.     

激光快速成型TC4合金显微组织及力学性能

采用金相显微镜、扫描电镜、电子拉伸机等，研究了激光快速成型TC4合金沉积态在平行沉积方向和垂直沉积方向的组织和力学性能.结果表明:激光快速成型TC4合金沉积态宏观组织沿沉积方向生长的粗大β柱状晶呈明暗相间的条带状结构，具备典型的魏氏组织特征;垂直沉积方向的强度比平行沉积方向的强度高，但塑性低;合金断口为韧窝状断口，垂直沉积方向的断口韧窝尺寸比平行沉积方向的小.     

冷轧带钢局部高点卷取过程起筋控制的建模与仿真

为了研究带钢局部高点卷取起筋的控制方法，利用三维弹塑性变形基本理论，并引入带钢塑性流动因子，建立了弹塑性卷取应力和起筋量模型.基于应力函数假设、S. Timoshenko最小功原理和伽辽金虚位移法建立了起筋带钢的应力场分布和可用于在线计算的起筋临界卷取张力设定模型.仿真结果表明：局部高点在径向累积叠加所引起的带钢张力不均匀分布和轴向压应力是导致带钢起筋的主要原因；起筋量随局部高点高度、卷径和卷取张力增加而增大，薄带钢比厚带钢起筋量增幅明显；临界卷取张力随卷径、带钢厚度和局部高点高度增大而减小.     

运用试验设计法优化某军品压铸弹尾工艺

根据某军品部件出现的问题，应用试验设计法成功地找出了最优组合，提高了该部件的强度，解决了该强度问题，使生产得以正常进行。     

矩形型钢弯曲回弹曲率半径r值的确定

文章在分析矩形型钢弯曲变形过程及应力与应变等方面的关系的基础上，推导出工件曲率半径与工件回弹后曲率半径之间的关系，从而确定了凸模半径。     

铅锡合金沉积物的显微组织

将离子浓度比为5∶5的铅锡电沉积分形生长沉积物制备成金相样品，用金相显微镜观察了它们的显微组织。结果表明，在此情况下，铅锡电沉积生成物由两相组成，即铅锡共晶相和铅基固溶相，两相呈交替层状分布。